The World's #1 Vacuum Cleaner Advice, Repair, Discussion & Information Forum

Author Topic: dyson dc40 brushbar not turning  (Read 28213 times)

Offline tjncfc54

  • Member
  • Posts: 3
Re: dyson dc40 brushbar not turning
« Reply #30 on: October 29, 2016, 04:36:10 PM »
Hi, tested the brush head on my DC40 and it's fine. The brush head switch is fine but no power to the socket at the brush head. So it's definitely the yoke cable at fault. I've tried to remove the yoke but haven't succeeded yet. Anybody have a link or idiots guisde to remove the yoke to get to the cable please?

Online Parwaz7862

  • Member
  • Posts: 2971
  • Country: gb
  • Gender: Male
  • DYSON DYSON DYSON!!!!!!!!! 😃😃😃
Re: dyson dc40 brushbar not turning
« Reply #31 on: October 29, 2016, 10:30:00 PM »
It's similar to a DC41 yolk replacement. It's been almost two years since I owned a DC40 so I'm going by memory:
Remove the hose from the back of the vacuum's ball
Remove the balls (Filter side and unscrew all the visible screws for the filter holder grill
and the other side has a glamour cap which needs to be turned anti clockwise, then there's a black ring which needs to be turned anticlockwise to be screwed off

The left hand side will then come off. Remove the two screws  holding the semi circular white bracket and all the visible screws from underneath the yolk and both sides. The yolk assembly then comes off from both sides of the motor housing and it's pretty easy when you do it, it may look hard but it's much easier than you think ;)
DC14s are tanks, just need a slightly longer motor life. Do plastic parts often break on DC14s? Nope. DC41- Sexy looking futuristic and powerful machine. Just needs a better designed cleaner head wheel and cyclone clip along with a dense metal rod in the chassis.

Offline tjncfc54

  • Member
  • Posts: 3
Re: dyson dc40 brushbar not turning
« Reply #32 on: October 30, 2016, 04:33:57 PM »
Hi, thanks so much. I was almost there without actually knowing it. What a horrible design that yoke wiring etc is! Whoever designed that should be ashamed. Got it all back together apart and working from the toothed notched wheel thing. I just couldn't line it up with it on so removed it. Then when I put it all back together I couldn't get enough clearance / room to refit it. What does it actually do because it locks in postion upright without it.

Online Parwaz7862

  • Member
  • Posts: 2971
  • Country: gb
  • Gender: Male
  • DYSON DYSON DYSON!!!!!!!!! 😃😃😃
Re: dyson dc40 brushbar not turning
« Reply #33 on: October 30, 2016, 04:58:58 PM »
You're welcome :)
Glad to hear it worked out well for you ;)
DC14s are tanks, just need a slightly longer motor life. Do plastic parts often break on DC14s? Nope. DC41- Sexy looking futuristic and powerful machine. Just needs a better designed cleaner head wheel and cyclone clip along with a dense metal rod in the chassis.

Offline tjncfc54

  • Member
  • Posts: 3
Re: dyson dc40 brushbar not turning
« Reply #34 on: October 30, 2016, 08:20:52 PM »
Got it all back together apart and working from the toothed notched wheel thing. I just couldn't line it up with it on so removed it. Then when I put it all back together I couldn't get enough clearance / room to refit it. What does it actually do because it locks in postion upright without it.

Online Parwaz7862

  • Member
  • Posts: 2971
  • Country: gb
  • Gender: Male
  • DYSON DYSON DYSON!!!!!!!!! 😃😃😃
Re: dyson dc40 brushbar not turning
« Reply #35 on: October 30, 2016, 09:07:19 PM »
Not really sure of the intended purpose, sorry.
DC14s are tanks, just need a slightly longer motor life. Do plastic parts often break on DC14s? Nope. DC41- Sexy looking futuristic and powerful machine. Just needs a better designed cleaner head wheel and cyclone clip along with a dense metal rod in the chassis.

Offline MikeM

  • Member
  • Posts: 3
  • Country: gb
  • Gender: Male
Re: dyson dc40 brushbar not turning
« Reply #36 on: December 06, 2016, 10:10:18 AM »
Hi All,

I just wondered what tools i will need to disassemble the DC40 to replace the yoke cable? I am hoping to fix my dyson this afternoon after work so if you know what tools are needed i can take some home for the evening. Any replies by 2pm will be much appreciated!

Mike

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 4495
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: dyson dc40 brushbar not turning
« Reply #37 on: December 06, 2016, 10:14:39 AM »
Hi All,

I just wondered what tools i will need to disassemble the DC40 to replace the yoke cable? I am hoping to fix my dyson this afternoon after work so if you know what tools are needed i can take some home for the evening. Any replies by 2pm will be much appreciated!

Mike

We sell >>these<< for such a job. Take those sizes home if you have them.

Offline MikeM

  • Member
  • Posts: 3
  • Country: gb
  • Gender: Male
Re: dyson dc40 brushbar not turning
« Reply #38 on: December 06, 2016, 12:03:31 PM »
Ah brilliant thankyou. I have the T10 & 15 sizes but not the T8. Will have to wait a few days and order one online

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 4495
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: dyson dc40 brushbar not turning
« Reply #39 on: December 06, 2016, 05:18:46 PM »
Ah brilliant thankyou. I have the T10 & 15 sizes but not the T8. Will have to wait a few days and order one online

You may not actually need the T8 for that job, see how you go with the T10 and T15.

Offline MikeM

  • Member
  • Posts: 3
  • Country: gb
  • Gender: Male
Re: dyson dc40 brushbar not turning
« Reply #40 on: December 06, 2016, 06:30:49 PM »
So I have got his far but don't know what to do from this point on? Don't know what needs removing etc? Any ideas?

ila_rendered

Offline rob_520

  • Member
  • Posts: 17
Re: dyson dc40 brushbar not turning
« Reply #41 on: March 20, 2017, 08:36:56 PM »
has anyone got a pictures of where the wiring loom goes back with the clips.  as they just fell out when taken part .need to put a new loom in but need to know where the wiring feeds plus where the clips go.  pictures would really help many thanks

Dyson Spare Parts


 

 

Dyson Spare Parts

 

 

Dyson Universal Adaptor

 

 

Buy a Dyson DC04 Wand Handle

 

 

 

 

The Dyson Medic Blog

Dyson Spares, Parts, Advice   Follow us on Twitter

Manchester Vacson Google+

Manchester Vacs on Instagram