The World's #1 Vacuum Cleaner Advice, Repair, Discussion & Information Forum

Author Topic: DC03 Clear - Stripdown and Refurb  (Read 24739 times)

Offline Ben

  • Member
  • Posts: 12
  • Country: gb
  • Gender: Male
Re: DC03 Clear - Stripdown and Refurb
« Reply #60 on: June 06, 2020, 06:35:57 PM »
They are very rare and very fragile. You'll struggle to find one.

The only one we have - and this may be the same as the one you describe you have already - is one that is more of a solid blue in colour. I think later ones were fitted with those.
This isnít about the handle this time. Iíve just finished reassembling the cleaner and Iíve stripped the clutch and changed the belts. The problem is that it makes that awful ratcheting sound when I go to recline the machine. However if you recline it without the machine being turned on and start it from the reclined position itís fine. Iíve refurbished a few dc03 and whenever Iíve replaced the belts theyíve had the exact same issues but Iíve never had this problem on a dc04,14,33. Do you think the machine needs a new clutch or is it my error. If it helps itís the original from 1998 and it has a metal clutch cog and a metal cover instead of the white ones used not long after. Any suggestions would be much appreciated as I would love to have it 100% functional and not have to faf about when using it
Dyson collector and restorer

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 5662
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: DC03 Clear - Stripdown and Refurb
« Reply #61 on: June 06, 2020, 07:20:00 PM »
Assuming it's assembled correctly in the machine, if it didn't do that before, you've made a mistake rebuilding the clutch. They do that when they're jammed. We routinely rebuild the older clutches with metal parts, so there's nothing obsolete in there. 

I can ask our chap on Monday if there's anything specific to those clutches that differs. I'm not aware there is but I'll ask.

Offline Ben

  • Member
  • Posts: 12
  • Country: gb
  • Gender: Male
Re: DC03 Clear - Stripdown and Refurb
« Reply #62 on: June 06, 2020, 08:18:44 PM »
Assuming it's assembled correctly in the machine, if it didn't do that before, you've made a mistake rebuilding the clutch. They do that when they're jammed. We routinely rebuild the older clutches with metal parts, so there's nothing obsolete in there. 

I can ask our chap on Monday if there's anything specific to those clutches that differs. I'm not aware there is but I'll ask.
Just stripped it down again and everything looked ok. When I put it back in I made sure that the brushroll spun as freely as it possibly could. Still making the horrible noise, I donít know if itís because of how fast the cleanerhead makes contact with the floor because itís quite fast leaving  no time for the clutch to engage properly but at this point Iím stumped.
Dyson collector and restorer

Offline Ben

  • Member
  • Posts: 12
  • Country: gb
  • Gender: Male
Re: DC03 Clear - Stripdown and Refurb
« Reply #63 on: June 07, 2020, 04:07:13 PM »
Assuming it's assembled correctly in the machine, if it didn't do that before, you've made a mistake rebuilding the clutch. They do that when they're jammed. We routinely rebuild the older clutches with metal parts, so there's nothing obsolete in there. 

I can ask our chap on Monday if there's anything specific to those clutches that differs. I'm not aware there is but I'll ask.
I donít know if this makes a difference but if you leave the machine switched off, recline it and make sure itís in the drive position so that when you spin the brushroll it turns the motor. If you spin it with your hand with a bit of force you can feel the clutch slipping and jamming up. Iíve tried the exact same thing with 2 dc04s that I have in my room and neither of them do the same thing. As the machine is clear and you can see the clutch belt on the motor spindle it all looks to be lined up correctly with no problems. I think the next step is to buy a new clutch that you are selling at the minute as Iíd like this machine to work to 100% of its capabilitiy
Dyson collector and restorer

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 5662
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: DC03 Clear - Stripdown and Refurb
« Reply #64 on: June 08, 2020, 05:19:23 PM »
Our chap says there are a couple of different set ups on early clutches, and if not a faulty internal component, it may be to do with the spacers. Different versions have differences - some have 2 some have 3 - and he cant speculate unless its in front of him.

A recon clutch might be the short answer.

Offline Ben

  • Member
  • Posts: 12
  • Country: gb
  • Gender: Male
Re: DC03 Clear - Stripdown and Refurb
« Reply #65 on: June 08, 2020, 07:30:17 PM »
Our chap says there are a couple of different set ups on early clutches, and if not a faulty internal component, it may be to do with the spacers. Different versions have differences - some have 2 some have 3 - and he cant speculate unless its in front of him.

A recon clutch might be the short answer.
Itís t he very early type with t he 3 spacers in, a metal cog and a metal backplate which the friction material sits into if that helps.
Dyson collector and restorer

Dyson Cylinder Spare Parts


 

FFP2 N95 Face Masks

Dyson Spare Parts

Freestanding Dyson Cordless Vacuum Stand

Buy a Dyson DC04 Wand Handle

Sebo Vacuum Cleaners

Instagram

Dyson Spares, Parts, Advice†††Follow us on Twitter

Manchester Vacson Google+

Manchester Vacs on Instagram