The World's #1 Vacuum Cleaner Advice, Repair, Discussion & Information Forum

Author Topic: Dyson Dc04 wont tilt back  (Read 12277 times)

Offline chivvy

  • Member
  • Posts: 5
Dyson Dc04 wont tilt back
« on: May 03, 2015, 12:01:59 pm »
Hi,

I have the opposite issue of "Dyson DC04 won't stand up".

Mine stands up ok but when I want to use it I have to apply an awful lot of pressure to the soleplate in order to get the handle to tilt back. When it does tilt back it is with a very loud cracking noise.

Can't see anything obviously wrong or out of alignment.

Any advice gratefully received.

Regards

Pete

Offline beko1987

  • Member
  • Posts: 5044
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson Dc04 wont tilt back
« Reply #1 on: May 03, 2015, 09:14:23 pm »
Whats the state of the little black wheel that sits under the brushroll housing?

You can just about see it with the machine reclines (sorry!) And the little wheel should move freely. If you get it moving a drop of oil helps.
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Offline chivvy

  • Member
  • Posts: 5
Re: Dyson Dc04 wont tilt back
« Reply #2 on: May 04, 2015, 09:17:45 am »
I can't see any little black wheel.

The base rotates freely when it's reclined though, it's just the unclipping from the upright position that is a problem.

Offline beko1987

  • Member
  • Posts: 5044
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson Dc04 wont tilt back
« Reply #3 on: May 04, 2015, 09:27:29 am »
If you can't see a wheel then it may be missing, I'll get a photo later so you can confirm. Basically, from upright, the wheel and sprung lever have to go over a kink in the motor housing to release, if everything's not working spot on this can be tricky as the wheel doesn't ride over the kink and out the other side
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Offline Sleaford White

  • Member
  • Posts: 269
  • Country: gb
Re: Dyson Dc04 wont tilt back
« Reply #4 on: May 04, 2015, 09:31:04 am »
Beko's right. On the underside of the foot plate there is a plastic bracket with spring and small wheel, approximately 1cm in diameter. Make sure that it's free to rotate. You can also reduce the tension in the spring by chopping a bit off.

Offline chivvy

  • Member
  • Posts: 5
Re: Dyson Dc04 wont tilt back
« Reply #5 on: May 04, 2015, 09:40:04 am »
If you can't see a wheel then it may be missing, I'll get a photo later so you can confirm. Basically, from upright, the wheel and sprung lever have to go over a kink in the motor housing to release, if everything's not working spot on this can be tricky as the wheel doesn't ride over the kink and out the other side

That sounds exactly like my issue. If you're able to post a pic so that I can check I'm looking for the ball in the right place that would be a great help.

Offline Parwaz7862

  • Member
  • Posts: 3412
  • Country: gb
  • Gender: Male
  • Dyson geek 😃
Re: Dyson Dc04 wont tilt back
« Reply #6 on: May 04, 2015, 10:21:08 am »

Offline chivvy

  • Member
  • Posts: 5
Re: Dyson Dc04 wont tilt back
« Reply #7 on: May 04, 2015, 10:27:21 am »
Thankyou all

Offline chivvy

  • Member
  • Posts: 5
Re: Dyson Dc04 wont tilt back
« Reply #8 on: May 04, 2015, 10:45:11 am »
Just dismantled it, the little wheel was still on the lever but was very stiff. I put some vaseline on it and reassembled.

All good now. Again, thanks to everyone for their help and advice.

Regards

Pete

Offline beko1987

  • Member
  • Posts: 5044
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson Dc04 wont tilt back
« Reply #9 on: May 04, 2015, 12:42:05 pm »
 :thumbsup:

Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Offline meakin65

  • Member
  • Posts: 1
Re: Dyson Dc04 won't recline easily
« Reply #10 on: August 15, 2020, 07:16:36 pm »
Can somebody tell me if the small wheel that allows the DC04 to recline is available as a spare? Mine is missing?

Offline MVacs

  • Administrator
  • Member
  • *****
  • Posts: 6374
  • Country: gb
  • Gender: Male
    • Manchester Vacs - The Independent Dyson Specialists
Re: Dyson Dc04 wont tilt back
« Reply #11 on: August 16, 2020, 07:19:04 pm »
You'll find it here.

Put in the order comments if you have clutched or non clutched as there are two types.

DC04 Spare Parts


 

 

Trade Dyson Spare Parts

 

 

Dyson Spare Parts

 

 

Freestanding Dyson Cordless Vacuum Stand

 

 

Buy a Dyson DC04 Wand Handle

 

 

 

 

Buy a police truncheon

 

 

Instagram

Dyson Spares, Parts, Advice   Follow us on Twitter

Manchester Vacs on Instagram