The World's #1 Vacuum Cleaner Advice, Repair, Discussion & Information Forum

Author Topic: Lower filter stuck  (Read 4064 times)

Offline helvelyn

  • Member
  • Posts: 1
  • Country: gb
  • Gender: Male
Lower filter stuck
« on: September 22, 2015, 01:54:54 AM »
I am having poor suction on my DC03, especially from the hose. I have checked the hose, cyclone, cassette, and no obstructions or breaks. I'm now checking the filters. The top filter came out with a bit of a struggle - I had to bend the top of the housing upwards a bit, but the lower (post-motor) filter is firmly stuck. I tried pulling it out with the plastic loop, but the loop broke off. I'm reluctant to try pulling it out with pliers for fear of damaging the connection surface. Any ideas what could be causing it to stick, and more importantly how to free it without (too much) damage?

Also the various seals are all in place but some look a bit tired, especially the round flap-valve in the cassette. It is not fully closed by about 3mm when the machine is off, but the vacuum seems to pull it closed when running. Is that normal or should I replace it?

Thanks

Phil

Offline Madrat

  • Member
  • Posts: 2926
  • Country: england
  • Gender: Male
Re: Lower filter stuck
« Reply #1 on: September 22, 2015, 11:43:26 AM »
Not sure but does it twist first?

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 5873
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: Lower filter stuck
« Reply #2 on: September 22, 2015, 07:34:52 PM »
The case twists to get the top filter out.

ila_rendered

But the one underneath appears to just pull out.

ila_rendered

Its a while since I have done one to be honest. Lets see if anyone else has had one in bits more recently.

Offline Madrat

  • Member
  • Posts: 2926
  • Country: england
  • Gender: Male
Re: Lower filter stuck
« Reply #3 on: September 22, 2015, 07:44:31 PM »
Must have been case I was thinking of, wonder if its just stuck with dirt, or perhaps slightly melted if motor has got hot, try rocking it.

Offline Parwaz7862

  • Member
  • Posts: 3402
  • Country: gb
  • Gender: Male
  • Dyson geek 😃
Re: Lower filter stuck
« Reply #4 on: September 23, 2015, 01:48:52 AM »
Turn the machine upside down, turn the filter and it should fall out :)
DC14s are tanks, just need a slightly longer motor life. Do plastic parts often break on DC14s? Nope. DC41- Sexy looking futuristic and powerful machine. Just needs a better designed cleaner head wheel and cyclone clip along with a dense metal rod in the chassis.

Offline neilB

  • Member
  • Posts: 2
Re: Lower filter stuck
« Reply #5 on: April 05, 2021, 03:14:41 PM »
Isnít the lower filter a ďlifetimeĒ HEPA whatever that means.
Shouldnt need changing ?

Offline dysondestijl

  • Member
  • Posts: 112
  • Country: gb
Re: Lower filter stuck
« Reply #6 on: April 06, 2021, 12:57:09 AM »
They are a lifetime filter. But I can imagine Dyson didnít envisage them lasting 24 years (they were released in 1997) so if the machine has been well used, the filters are probably a bit past it now!
I would imagine their definition of Lifetime was probably 5-10 years!

Offline neilB

  • Member
  • Posts: 2
Re: Lower filter stuck
« Reply #7 on: April 06, 2021, 11:47:09 AM »
Good point - who knows what lifetime means. But you donít seem to list a replacement

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 5873
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: Lower filter stuck
« Reply #8 on: April 07, 2021, 07:18:39 PM »
Good point - who knows what lifetime means. But you donít seem to list a replacement

If it looks clean I wouldn't bother replacing it. It's an exhaust filter. DC03s were very well filtered.

Dyson Cylinder Spare Parts


 

FFP2 N95 Face Masks

Dyson Spare Parts

Freestanding Dyson Cordless Vacuum Stand

Buy a Dyson DC04 Wand Handle

Sebo Vacuum Cleaners

Instagram

Dyson Spares, Parts, Advice†††Follow us on Twitter

Manchester Vacson Google+

Manchester Vacs on Instagram