The World's #1 Vacuum Cleaner Advice, Repair, Discussion & Information Forum

Author Topic: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment  (Read 1706 times)

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #30 on: July 23, 2017, 10:17:47 PM »
Time to fit the release valve now

ila_rendered

Lovely

ila_rendered

The seal for the cyclone fitted to the air duct end

ila_rendered

And after feeding the cables thorugh their relevant holes the PCB holder fits to the lower chassis

ila_rendered

Here is where the issues started, the spinal cord didn't route properly which meant the PCB part didn't screw down fully, so eventually I just removed the spine and fiddled about with it for 10 minutes

ila_rendered

Done!

ila_rendered

Wired up

ila_rendered

The brushroll loom had to be fed down now, it sits in this channel here

ila_rendered

The inner PCB cover can be fitted now

ila_rendered
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #31 on: July 23, 2017, 10:25:44 PM »
Jumping somewhere else first though, the ball runner wheels are fitted to the outer shell

ila_rendered

The inner hose is clipped in

ila_rendered

The clear plastic cog part is refitted

ila_rendered

The stabilizer bar is clipped in

ila_rendered

Then the 2 washers and retaining cage are screwed onto the filter side of the assembly

ila_rendered

The whole shebang is then fitted to the machine and screwed down

ila_rendered

It took me a few minutes to work out how the part that fell out nearly as soon as I started then fitted, but it holds the brushroll loom tight against the housing and runs up and down the pivot point, it didn't go together too well either but held up well enough. The plug that sits at the bottom of the machine is a sod too, one wrong move and it unclips and pulls all the wires out

ila_rendered

Post filter back plate is screwed down

ila_rendered

And the machine stands up now!

ila_rendered
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #32 on: July 23, 2017, 10:29:44 PM »
Post filter and wheels fitted (their not balls!)

ila_rendered

Brushroll housing fitted

ila_rendered

Tool holder fitted

ila_rendered

I fed the cable up the spine and clipped the lower cord hook on

ila_rendered

Then wired up the switches

ila_rendered

And fitted the cover

ila_rendered

Top handle clipped on



Wand cap fitted to the handle cover

ila_rendered

Then clipped onto the machine. Tools inserted (and yes I know the upholstery tool was the wrong way round!)



Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #33 on: July 23, 2017, 10:32:58 PM »
Hose fitted

ila_rendered

Wand button and cord hook refitted

ila_rendered

And with the wand fitted to the machine it is DONE!!!!





ila_rendered



But, the big question, does it actually work? Has my first time having one of these a bit apart been for nothing?

<a href="https://www.youtube.com/watch?v=p-5jst4bRTE" target="_blank">https://www.youtube.com/watch?v=p-5jst4bRTE</a>

Yes, get in!

Thanks for reading (apart from Rusty Skull, he never reads these!)
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Online MVacs

  • Administrator
  • Member
  • *****
  • Posts: 4713
  • Country: gb
  • Gender: Male
    • Manchester Vacs -- The Independent Dyson Specialists
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #34 on: July 23, 2017, 11:10:44 PM »
Epic rebuild topic!  :bow:

Now in the stickies.  :icon_nod:

Online oldmoley

  • Member
  • Posts: 51
  • Country: gb
  • Gender: Male
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #35 on: July 24, 2017, 09:21:46 PM »
Beautifully timed! I've just been given one of these with a blown motor, so it's out with the tools then.....

Online mrdyson

  • Member
  • Posts: 96
  • Country: gb
  • Gender: Male
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #36 on: July 24, 2017, 09:35:06 PM »
Great work - well done.  :thumbsup:

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #37 on: July 24, 2017, 09:36:59 PM »
Thanks!
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Online dragoncurt

  • Member
  • Posts: 147
  • Country: gb
  • Gender: Male
  • Dyson FTW !
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #38 on: August 25, 2017, 10:11:59 PM »
How is the best way to clean the wand as I bought one of these and it's not clean and I've tried cleaning it with some warm water and soap but it's just not cutting it or in this case cleaning it :)

Nice pictures too. Thanks

Online Dysonboy

  • Member
  • Posts: 57
  • Country: 00
  • Gender: Male
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #39 on: August 26, 2017, 03:17:16 AM »
Longest thread of a rebuild yet??

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #40 on: August 26, 2017, 09:11:01 AM »
Close I reckon!

But guess who had a DC41 in the boot ready for a rainy day...
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Offline sheltonmath

  • Member
  • Posts: 1
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #41 on: September 02, 2017, 02:19:38 AM »
Thank you. This was very helpful to me, in refurbishing my DC65. I wish I would have taken pictures. :snivel:

Offline dsam

  • Member
  • Posts: 15
  • Country: gb
  • Gender: Male
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #42 on: October 09, 2017, 09:32:15 PM »
Hi, great tutorial, however im missing a wheel of mine and need to take 1 off an old carcass to replace it. How do they come off? im thinking they jus pull off, is this right dont want to damage the spare one.

Online beko1987

  • Member
  • Posts: 3696
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Dyson DC40 Mk1 (Pre EU) - Stripdown and Refurbishment
« Reply #43 on: October 09, 2017, 09:59:58 PM »
Hi, great tutorial, however im missing a wheel of mine and need to take 1 off an old carcass to replace it. How do they come off? im thinking they jus pull off, is this right dont want to damage the spare one.

That I don't know, as I left that alone! I've found the wheels on ball models tricky to get off, and broke a dc19 wheel assembly before trying! You'll probably find it easier and not much more expensive to get and change the whole wheel assembly!
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Dyson Spare Parts


 

 

Dyson Spare Parts

 

 

Sebo Vacuum Cleaners

 

 

Buy a Dyson DC04 Wand Handle

 

 

 

 

The Dyson Medic Blog

Dyson Spares, Parts, Advice   Follow us on Twitter

Manchester Vacson Google+

Manchester Vacs on Instagram