The World's #1 Vacuum Cleaner Advice, Repair, Discussion & Information Forum

Author Topic: Stripping down a dc14 cyclone  (Read 836 times)

Offline Dysonboy123

  • Member
  • Posts: 84
Stripping down a dc14 cyclone
« on: April 18, 2019, 12:55:31 PM »
Is  it recommended

Online ryevac

  • Member
  • Posts: 426
  • Country: gb
  • Gender: Male
  • Optimism is the faith that leads to achievement
Re: Stripping down a dc14 cyclone
« Reply #1 on: April 18, 2019, 02:22:01 PM »
Why not ? lid off, watch the spring and plastic peg at the rear, gasket cover off and wash the rubber gasket too.
Don't get the screws mixed up as the lid uses different to the gasket cover.
Bottom comes off with a bit of muscle, just pour a little boiling water over it first so no lever tools required
The only way to fail is not to try.

Offline Dysonboy123

  • Member
  • Posts: 84
Re: Stripping down a dc14 cyclone
« Reply #2 on: April 18, 2019, 10:57:37 PM »
I've putted it all together but the lid that goes on the gasket doesn't fit it properly.

Online ryevac

  • Member
  • Posts: 426
  • Country: gb
  • Gender: Male
  • Optimism is the faith that leads to achievement
Re: Stripping down a dc14 cyclone
« Reply #3 on: April 19, 2019, 12:36:32 AM »
you have the gasket fitted incorrectly
The only way to fail is not to try.

Offline Dysonboy123

  • Member
  • Posts: 84
Re: Stripping down a dc14 cyclone
« Reply #4 on: April 19, 2019, 01:04:28 AM »
I've fitted correctly.

Offline Dysonboy123

  • Member
  • Posts: 84
Re: Stripping down a dc14 cyclone
« Reply #5 on: April 19, 2019, 01:05:22 AM »
Some side stick out some dont.

Online ryevac

  • Member
  • Posts: 426
  • Country: gb
  • Gender: Male
  • Optimism is the faith that leads to achievement
Re: Stripping down a dc14 cyclone
« Reply #6 on: April 19, 2019, 01:36:32 AM »
take it to bits and re fit correctly

I can photo one tomorrow for you if stuck
The only way to fail is not to try.

Offline Dysonboy

  • Member
  • Posts: 159
  • Country: 00
  • Gender: Male
Re: Stripping down a dc14 cyclone
« Reply #7 on: April 19, 2019, 01:38:32 AM »
Is  it recommended
Definitly! It will work much better when cleaned - besides.. If we don't take it apart, how can we clean it out for refurbishment?

I've putted it all together but the lid that goes on the gasket doesn't fit it properly.
The gasket must not be sat quite right around the lid as Ryevac said.
Collector and restorer of most vacuum cleaners including vintage, older style models and newer models. Seller of refurbished vacuums and vacuum parts Livin' every day, as if it were the last!

Offline Dysonboy123

  • Member
  • Posts: 84
Re: Stripping down a dc14 cyclone
« Reply #8 on: April 19, 2019, 11:14:51 AM »
take it to bits and re fit correctly

I can photo one tomorrow for you if stuck

Yes that would fine.

Offline Dysonboy123

  • Member
  • Posts: 84
Re: Stripping down a dc14 cyclone
« Reply #9 on: April 19, 2019, 12:17:02 PM »
Can you wash the rubber gasket or not?
It's the one that sits under the washable filter.

Offline beko1987

  • Member
  • Posts: 4517
  • Country: gb
  • Gender: Male
  • Let's take it apart!
    • My blog
Re: Stripping down a dc14 cyclone
« Reply #10 on: April 19, 2019, 04:44:37 PM »
You can wash it all! If it's a day like it is where I am where you are it'll be dry in an hour in the sun!
Collector and restorer of vintage vacuums, Dyson Appreciator! Come and see my blog, where I am uploading all my mountains of brochures, manuals and other vacuum cleaner paperwork, and also my youtube channel @beko1987!

Online ryevac

  • Member
  • Posts: 426
  • Country: gb
  • Gender: Male
  • Optimism is the faith that leads to achievement
Re: Stripping down a dc14 cyclone
« Reply #11 on: April 19, 2019, 05:12:22 PM »
Looks just like the silver screws to remove, i was getting confused possibly with another vac i did t'other day

ila_rendered

ila_rendered

ila_rendered

ila_rendered

ila_rendered
The only way to fail is not to try.

Offline Dysonboy123

  • Member
  • Posts: 84
Re: Stripping down a dc14 cyclone
« Reply #12 on: April 19, 2019, 11:47:44 PM »
I've got it all back together, but the hole which holds the bin trigger doesn't properly align with the handle. Sorry if you think this is weird.

Offline Dysonboy

  • Member
  • Posts: 159
  • Country: 00
  • Gender: Male
Re: Stripping down a dc14 cyclone
« Reply #13 on: April 25, 2019, 05:44:30 PM »
I've got it all back together, but the hole which holds the bin trigger doesn't properly align with the handle. Sorry if you think this is weird.

They sometimes are a pain to get the bin flap release to sit right. Try disassembling the flap release rod and then re assembling. ive had this one a couple times.
Collector and restorer of most vacuum cleaners including vintage, older style models and newer models. Seller of refurbished vacuums and vacuum parts Livin' every day, as if it were the last!

DC14 Spare Parts


 

 

Dyson Spare Parts

 

 

Freestanding Dyson Cordless Vacuum Stand

 

 

Buy a Dyson DC04 Wand Handle

 

 

 

 

Sebo Vacuum Cleaners

 

 

Instagram

Dyson Spares, Parts, Advice   Follow us on Twitter

Manchester Vacson Google+

Manchester Vacs on Instagram